1/31/2024 0 Comments Fldigi user manual![]() Fldigi acts as the XMLRPC server and once Fldigi closes the gateway can’t connect to the server. The error message you are gettingwhen you close Fldigi is a normal message. When Fldigi is installed in the Program files structure Microsoft has a tendency to block communication between Fldigi and other applications as it put to much security on the Program files Structure. You do not need to re-install it just copy it from one directory to another. My other suggestion to you is to change the directory where Fldigi is located in. If you click the up arrow near the clock you should see its icon (Little Blue Man) double click on that and it will open the gateway back open. Clicking on an SSB spot always works ok.Īfter the gateway is loaded and it has connected to Fldigi it minimizes itself to the area near the clock. It’s consistently this way, but that’s just odd. NOW, here’s the strange part…If I click the spot several times (fairly quickly), it will move to the EXACT spot frequency (not with audio offset) and then magically populate the correct MODE in the capture window for DXKeeper (that part I want) The problem with that is there’s no audio offset and you can’t see the signal you’re looking for of course. It was previously set to PSK31, so even though you might be clicking on an RTTY spot, it would set it to PSK31. I’ve set the “Log Mode for PKT or PKT-R” selection in the Commander Options window to nothing (ie: blank) since it only allows a single option. When I click on a spot in SpotCollector, the spot is transferred to DXLabs apps and fldigi as normal, except the mode in the DXKeeper capture window is missing. My setup is an FTdx3000, using the internal sound card (which requires the rig to be in DATA-USB mode) with current version of fldigi and DXLabs suite with commander. I’ve spent hours trying to figure this out. In SETTINGS>Accounts>Account Editor, put checks in the Sync boxes as desired.Love the utility, but evidently I’m too stupid to make this work properly. When RigPi is controlling your radio, contacts logged in WSJT-X or Fldigi are transferred to your RigPi log. use the audio selections as used in WSJT-X, above. WSJT-X Manual: Click to open WSJT-X manualįldigi is a multi-mode digital communications program, written by Dave Freese, W1HKJ and team.Ģ.Audio: Configure>Sound Card>Audio>Devices. ![]() The CAT PTT setting is not used when you use Hamlib GPIO for PTT. Select Hamlib GPIO in the H/W PTT drop down list in Advanced Radio settings for PTT. Some radios do not have a PTT-by-CAT function. You must reboot RigPi to clear the error before resetting the audio device selection. This issue appears to be present in WSJT-X 2.4. Some selections may not display an error at first, but after clicking Tune, then restarting WSJT-X, the follwing error appears: If you use incorrect audio devices, WSJT-X will display a dialog warning of a problem: If using the RigPi Audio board (your radio doesn't have CODECs), make the following selections: (The CODECs in your radio may have a different name.) Radio 1 uses port 4532, radio 2 uses port 4534, and so on.ģ.Audio: If using a radio that has CODECs, choose the alsa_input and alsa_output devices in the Input and Output drop-down lists in WSJT-X File>Settings>Audio>Soundcard. The port will be different depending on which RSS account you are using. Use the following values:Ģ.Network Server: localhost: 4532. Start RigPi Station Server and connect the radio. The first time you start WSJT-X you are invited to enter your callsign and Grid locator.Ĭonnect to a radio from the File>Settings>Radio panel. To start WSJT-X, from the Raspberry Pi Desktop, open the applications menu and select Ham Radio>wsjtx. ![]() Frequency and Mode data are shared between RigPi and WSJT-X, and QSO information logged in WSJT-X is automatically transferred to RigPi Log. WSJT-X, written by Joe Taylor, K1JT, is installed on RigPi Server. WSJT-X is designed to provide reliable communications in extreme weak-signal conditions. Close Mumble before using WSJT-X or Fldigi. Only one program can use the audio system at a time. ![]() Mumble, WSJT-X and Fldigi use the Raspberry Pi audio system, either through CODECs in the radio or through the RigPi Audio board. Click Pi Menu>Ham Radio to access the added ham programs. Additional Ham software provided with RigPi Station Server is accessed through the Raspbian PIXEL Desktop.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |